模具厂常用之标准零配件
Locating Center Punch 定位中心冲头
Locating Pilot Pin 定位导梢
Locating Ring 定位环
Lock Block 压块
Locking Block 定位块
Locking Plate 定位板
Loose Bush 活动衬套
Making Die 打印冲子
Manifold Block 歧管档块
Master Plate 靠模样板
Match Plate 分型板
Mold Base 塑胶模座
Mold Clamp 铸模紧固夹
Mold Platen 模用板
Moving Bolster 换模保持装置
Moving Bolster Plate 可动侧模板
One Piece Casting 整体铸件
Parallel Block 平行垫块
Parting Line 分模线
Parting Lock Set 合模定位器
Pass Guide 穴型导板
Peened Head Punch 镶入式冲头 锤击强化冲头 钻杆凸模
Pilot Pin 定位销 导向销子
Pin Gate 针尖浇口
Plate 衬板
Pre Extrusion Punch 顶挤冲头
Punch 冲头
Puncher 推杆
Pusher Pin 衬套梢
Rack 机架
Rapping Rod 起模杆
Re-entrant Mold 凹入模
Retainer Pin 嵌件梢
Retainer Plate 托料板
Return Pin 回位梢
Riding Stripper 浮动脱模器
Ring Gate 环型浇口
Roller 滚筒
Runner 流道
Runner Ejector Set 流道顶出器
Runner Lock Pin 流道拉梢
Screw Plug 头塞
Set Screw 固定螺丝
Shedder 脱模装置
Shim 分隔片
Shoe 模座之上下模板
Shoot 流道
Shoulder Bolt 肩部螺丝
Skeleton 骨架
Slag Riser 冒渣口
Slide(Slide Core) 滑块
Slip Joint 滑配接头
Spacer Block 间隔块
Spacer Ring 间隔环
Spider 模蕊支架
Spindle 主轴
Sprue 注道
Sprue Bushing 注道衬套
Sprue Bushing Guide 注道导套
Sprue Lock Bushing 注道定位衬套
Sprue Puller 注道拉料 浇道推出杆 注道残料顶销
Spew Line 合模线
Square Key 方键
Square Nut 方螺帽
Square Thread 方螺纹
Limit Stop Collar 限位套
Stop Pin 止动梢
Stop Ring 止动环
Stopper 定位停止梢
Straight Pin 圆柱销
Stripper Bolt 脱料螺栓
Stripper Bushing 脱模衬套
Stripper Plate 剥料板
Stroke End Block 行程止梢
Submarine Gate 潜入式浇口
Support Pillar 支撑支柱 顶出支柱
Support Pin 支撑梢
Supporting Plate 托板
Sweep Template 造模刮板
Tab Gate 辅助浇口
Taper Key 推拔键
Taper Pin 拔锥梢 锥形梢
Teeming Pouring 浇注
Three Start Screw 三条螺纹
Thrust Pin 推力销
Tie Bar 拉杵
Tunnel Gate 隧道形浇口
Vent 通气孔
Wortle Plate 拉丝模板
模具术语翻译
Movable Mould Moving Half 动模
Fixed Clamp Plate Top Clamping Plate Top Plate 定模座板
Moving Clamp Plate Bottom Clamping Plate Bottom Plate动模座板
Upper Clamping Plate 上模座板
Lower Clamping Plate 下模座板
Cavity-retainer Plate 凹模固定板
Mould Core-retainer Plate 型芯固定板
Punch-retainer Plate 凸模固定板
Die Body Die Sleeve Die Blank 模套
Backing Plate Support Plate 支承板
Spacer Parallel 垫块
Ejector Housing Mould Base Leg 支架
Die Head 模头
根据国家标准,以下为部分压铸模具标准翻译
Die-Casting Die 压力铸造模具
Fixed Die Cover Die 定模
Fixed Clamping Plate 定模座板
Bolster Fixed Die 定模套板
Moving Die Ejector Die 动模
Moving Clamping Plate 动模座板
Sprue 直流道
Runner 横流道
Gate 内浇口
模具分类
Injection Mold 注塑模
Plastic Rubber Mould 塑胶模
Rubber Molding 橡胶成形
Hot Chamber Die Casting 热室压铸
Sand Mold Casting 砂模铸造
Extrusion Mold 挤出模
Multi-Cavity Mold 多模穴模具
Stack Mold, Stack Injection Mould 叠层模
Plaster Mold 石膏模
Three Plates Mold 三板模
Plain Die 简易模
Pierce Die 冲孔模
Forming Die 成型模
Progressive Die 连续模
Gang Dies 复合模
Shearing Die 剪边模
Cavity Die 型腔模
Riveting Die 铆合模
Compression Molding 压缩成型
Flash Mold 溢流式模具
Extrusion Mold 挤压式模具
Split Mold 分割式模具
Mould Cavity 型腔 母模
Mold Core 模芯 公模
Large Die Mold 大型模具
Precise Die Mold 精密模具
Complex Die Mold 复杂模具
Foaming Mould 发泡模具
Metal Die 金属模具
Plastic Mold 塑料模具
Press Tool Stamping Die Punch Die 冲压模具
Extrusion Die 挤压模具
Graphite Die 石墨模具
首先,博海科技对你浏览我们文章的感谢,如果你对模具中英文术语还有补充欢迎评论区与我们互动。如果你对某行业其它话题感兴趣,也欢迎评论区告诉我们,博海科技小编也会采纳定期更新的哦!